Download Full Auto Glock Conversion Manual PDF

TitleFull Auto Glock Conversion Manual
File Size1.0 MB
Total Pages13
Document Text Contents
Page 1

file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]

www.carburetor-manual.com

Would you like some Free Manuals?

http://carburetor-manual.com/free-shop-manual-club-t-13.html

Also visit http://freeshopmanual.com for more Free Manuals

Also Visit my website for 7 FREE Download Manuals starting
with this one.

"The ABC's of Carburetion"

Click Here Now

http://www.carburetor-manual.com/
http://carburetor-manual.com/free-shop-manual-club-t-13.html
http://carburetor-manual.com/free-shop-manual-club-t-13.html
http://freeshopmanual.com/
http://carburetor-manual.com/abc-of-carburetion-2.php

Page 2

FuliAutoGlock

CONVERT YOUR GLOCK TO FUlL~AUTO

CHOOSE YOUR FIREPOWER: SEMI OR FUll-AUTO

Please visit the bureau of Alcohol Tobacco and Firearms website at www.atf.treas.goY
and read the laws regarding the conversion of firearms to fully automatic fire:
Translated loosely, the legal jargon says that unless the finished device Is registered
with the ATF, or you possess special exempting qualifications, It Is Ule{jal to possess the
finished device or pieces whether or not it is installed 0f1 a GIod< handgun.

Glock is a registered trademark of Glock Ges.m.b.H. and has no affiliation with this
device.

Page 6

TROUBLESHOOTING

If your Glock slide does not close fully: First check to make sure you do not have extra
parts left over] Only the black plastic end cap should be extra. Then check to see that
the device Is FUllY seated In the end cap slots. If the device is unseated even a
fraction of an inch, it will cause your slide to not dose all the way. If this is still not the
cause, please repeat step 5. The dlsconnector must create a small channel in the
frame to allow the slide to operate freely.

If your Glock handgun fires full auto in BOTH selector rod positions, disassemble the
device and follow the instructiOllS on the modification page. Due to the fact that all
Glock handguns have Slightly different tolerances, the disconnector measurements
compensate for this fact. You will need to shorten the disconnector by following the
instructions on the following page. Remove extremely small amounts and test after
each small modification until the problem no longer persists. It is vitally important that
you remove only small portions between testings because if your Glock fires semi-auto
in both selector rod poSitions after filing, you have removed too much and will need to
get a new dlsconnector machined.

Page 7

Disconnector
Method (1)

Cremel

Area to be

I nstructi ons:

ification:

.. Cut Off Wheel
•• 09

Vice I Support

(1) Use a Dremel™ tool and a # 409 cut off wheel for
use In dlsconnector modification

(2) Carefully secure the disconnector in a vice
(3) Modify ONLY the area specified
(4) Remove extremely small amounts each time

Disconnector Modification:
Method (2)

Area to be

Instructions:

Back and forth
motion _

Sharpening Stone

(1) Move the disconnector back and forth on the
sharpening stone

(2) Modify ONLY the area specified
(3) Remove extremely SMALL amounts each time
(4) Test device after each SMALL modification

Page 12

·8799

.7602

.6893

5404

.5220

.4212 -----1
~-~------ ~- ~-~

I I
A • A c

NOTES

ALL CHAMFERS ARE .0197 045"

IW/.rT1N6 (I"OIf ~G1tlIP SWf1"G#I IS ""'ID/"tL. It IWMlI'tJ F"llitStI WU
-1II.aID- Ilol nit SSUt:tN SIJrT"c/l Wn'lI1'Wav" 1M A ~ .. l' u.

I

-~

I I
A D

..,.-- R .1 047

SEE ENlARGEMENT

I).. R 0885

.,'"

R .0850

R .04 13

GLOCK

SC'.AI F, 5:1 I SHEET': J OF J

Page 13

---~ -
...... --.. ,

/ \

I + \ I I
\ I
\ /

-

'"

Similer Documents